Plumbing 101: What You Must Have for Installing a Bathtub

Call Today

Just about everyone is bound to have their own unique concepts when it comes to A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub
Mounting a tub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a new one is also a reasonably challenging task. If the old tub is easily easily accessible, the task can relocate speedily; if you need to open up a wall surface to remove the old tub and also position the new bathtub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will require an assistant to leave the old tub and set in the new one. Ensure you have certified yourself for the job and fit attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is much better to think about utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This post will assist you mount a new tub in your washroom if you have actually already acquired a brand-new tub as well as do not need to transform the setup of your previous supply of water pipes.
Your devices and also product checklist should comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the limited gain access to that is often the case.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
    Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in location in between the faucet as well as the sink. Protect the tap in place with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Installing the Bath tub


    Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
    The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bathtub till the level reviews degree.
    To install taps, fit all-time low of the furthest versatile tap port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
    Turn on the water supply as well as examine all joints and also new pipework for leakages and also tighten them if required. Load the bathtub and likewise check the overflow outlet and also the regular electrical outlet for leakages.
    Lastly, deal with the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has actually been used a minimum of once as this will resolve it right into its final placement.

    Planning for the Installation


    Firstly, the sustaining structure provided with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets device to stop pressure on the tub.
    Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the provided washing machines.
    Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final setting.

    Tiling Around the Tub


    In the location where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, triggering the water to permeate the wall surface between the bathroom as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the tub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can crack relatively early if you do not take into consideration this movement before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is suggested to fit the floor tiles making use of water-resistant or water resistant glue and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    We were shown that article about Installing A Bathtub from a friend on a different website. Liked our blog entry? Please share it. Help others discover it. We appreciate reading our article about How to Install a Bathtub.


    Source This Article

    Leave a Reply

    Your email address will not be published. Required fields are marked *